Select Page

How to configure raid in HP Z840 workstation

Power on your workstation and press Ctrl + C in the post screen

now you can find LSI config utility is initializing

with in the utility you can find the LSISAS2308 adapter

select it

in the next screen select raid properties

in the next screen you can find available raids , in our case we have used 512 mb x 3 ssd’s

in the current configuration of this workstation available raid is Raid 1 , Raid 1E , and 10 , and Raid 0

i have selected Raid 1E

in the next menu you have to select raid disks from no to yes and Press “ C “ create raid

in the next menu select “Save changes then exit this menu “

done

How to Enable Nic Teaming in Windows Server 2012 r2

  • In Server Manager, click Local Server.
  • In the Properties pane locate NIC Teaming, and then click the link Disabled to the right. The NIC Teaming dialog box opens.
  • In Adapters and Interfaces, select the network adapters that you want to add to a NIC Team.
  • Click TASKS or Right Click, and then click Add to New Team.
  • The New team dialog box opens and displays network adapters and team members. In Team name, type a name for the new NIC Team.you can get an option to select interface then click okay
  • after that go and check your network adapters , now you can see a new adapter with Nic team name, change ip in that adapter, done

enjoy

How to fix Autoconfiguration IPv4 Address issue Windows Server 2012 r2

Today when i install Windows Server 2012 r2 OS in a new HPE Proliant DL 380 server, after the os installation i have added ip manually to the Ethernet interface, but i get a Limited Access error,so i double check the ip is correct or not, i was right ip is correct, so i disabled firewall ,then i checked by typing ipconfig in the command prompt and i get result as follows

 

Ethernet adapter Ethernet:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : HP Ethernet 1Gb 4-port 331T Adapter
Physical Address. . . . . . . . . : 3C-A8-2A-F3-CF-9C
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::f0e1:58c8:4e40:4513%12(Preferred)
IPv4 Address. . . . . . . . . . . : 10.60.148.43(Duplicate)
Subnet Mask . . . . . . . . . . . : 255.255.255.224
Autoconfiguration IPv4 Address. . : 169.254.69.19(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . : 10.60.148.33
DNS Servers . . . . . . . . . . . : 10.60.148.36
10.1.12.43
NetBIOS over Tcpip. . . . . . . . : Enabled

 

as you can see there is two ipv4 ip's , one is the ip which i given , second is APIPA range ip

 

to fix this please follow the steps

  1. Click on start and click on RUN (or simple press windowsKey+R ) type CMD
  2. type ipconfig

this is will give you following result

 

Ethernet adapter Ethernet:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : HP Ethernet 1Gb 4-port 331T Adapter
Physical Address. . . . . . . . . : 3C-A8-2A-F3-CF-9C
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::f0e1:58c8:4e40:4513%12(Preferred)
IPv4 Address. . . . . . . . . . . : 10.60.148.43(Duplicate)
Subnet Mask . . . . . . . . . . . : 255.255.255.224
Autoconfiguration IPv4 Address. . : 169.254.69.19(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . : 10.60.148.33
DNS Servers . . . . . . . . . . . : 10.60.148.36
10.1.12.43
NetBIOS over Tcpip. . . . . . . . : Enabled

now type below code in the command prompt

netsh interface ipv4 show inter

this will show you below resurlt

C:\\Users\\Administrator>netsh interface ipv4 show inter

 

Idx     Met         MTU          State                Name

---  ----------  ----------  ------------  ---------------------------

  1          50  4294967295  connected     Loopback Pseudo-Interface 1

 12          10        1500  connected     Ethernet

 13           5        1500  disconnected  Embedded LOM 1 Port 1

 14           5        1500  disconnected  Ethernet 2

 15           5        1500  disconnected  Embedded LOM 1 Port 2

 16           5        1500  disconnected  Ethernet 3

 17           5        1500  disconnected  Ethernet 4

 18           5        1500  disconnected  Embedded LOM 1 Port 3

 19           5        1500  disconnected  Embedded LOM 1 Port 4

 

 

 

check for the connected interface

from the above command result you can find the connected interface notedown its idx id which is 12 in my case but your id may vary , type following command with your idx id in the command prompt then press enter

netsh interface ipv4 set interface 12 dadtransmits=0 store=persistent

 

this will give you following result

C:\\Users\\Administrator>netsh interface ipv4 set interface 12 dadtransmits=0 store=persistent

Ok.

  1. Click on start and click on RUN (or simple press windowsKey+R ) type CMD and Type Services.msc a box will appear Search for DHCP client right click on it and Click on Properties click on Startup Type select Disable
  2. Now Click on Stop Button Below And click on Ok

* Note

  1. Unplug Your Lan Cable And Restart your System
  2. After Restart don't Plugin your Cable, Come again to Services.msc find DHCP client right click on it and Click on Properties click on Startup Type now select Automatic
  3. Click on Start button below and then Ok.
  4. Now Plugin your Lan Cable and Enjoy.

 

How to retrieve a serial from a remote computer

To find serial number of a given system ,you need system host-name of targeted machine , and it has to be online in the lan (network)

then open "cmd" then ping your hostname 

if you receive all 4 packets back that means your targeted machine is online in the lan

now type following command in the command prompt

wmic /NODE: "INDIA-L090" bios get serialnumber

In this tutorial i have used "INDIA-L090" as host name this may vary in your case

 

enjoy

How to remove WOUtempAdmin User Profile

I have got this error after updating system using WSUS Offline utility,after successful update system restarts And the login screen by default shows the username of WOUTempAdmin. Not a big deal as I can log in with my admin account. But still a pain.

to fix this issue you have to follow the steps:

Press "Windows Key" and "R"

type "regedit" press Ok

Run "regedit" this will open Registry Editor

Note* Be careful when editing the registry. Don’t go into the registry editor and delete anything or change a setting unless you know exactly what you’re doing. If you do know what you’re doing and are careful to modify only the correct values, you shouldn’t have any problems. However, if you start deleting folders (known as “registry keys”) or modifying other values, you could seriously damage your Windows installation. When using the registry editor, always bear this warning in mind.

Navigate to HKEY_LOCAL_MACHINE\Software\Microsoft\Windows NT\CurrentVersion\Winlogon

 

Change DefaultUserName to your default user for eg: Administrator , i have used fragadmin0608 instead of Administrator this may vary

 

then within the registry you can find AutoAdminLogon

Press F3 and search for any entry containing "woutemplogin" and delete it as long as the searchphrase can't be found any more,then restart your system

After restart if you can see your login screen with your default username .then your issue is fixed

best of luck .

Pin It on Pinterest